Differences

This shows you the differences between two versions of the page.

--- documents:de4000:de4000install [2022/04/25 09:35]
rocky [3.11 Future Use]
+++ documents:de4000:de4000install [2022/12/13 14:48] (current)
twebster
@@ Line 1: / Line 1: @@
-=====Installation Instructions=====
+=====DE-4000 System Installation Instructions =====
+Last Modified:~~LASTMOD~~
-===DE-4000 Configurable Safety Shutdown and Control System===
-==Form DE-4000 II 4-22==
 This manual contains information on installing, wiring, and connecting to a DE-4000
@@ Line 112: / Line 109: @@
 System Configuration files can be created via a laptop or the HMI Display Module,
 saved and downloaded, as well as uploaded, to other DE-4000 Systems. This allows for configuration portability for users operating several similar systems.
+==== - Bootloader Files ====
+The Bootloader and current system versions can be updated in the Settings menu by connecting a USB drive containing the new firmware to the Controller Board.
 ==== - Trends ====
@@ Line 213: / Line 213: @@
 ===== - Additional Display Options =====
+==== - ACM-4000 (691810-1) ====
+The current configuration of the DE-4000 HMI display uses an ethernet connection to transfer data to it. Which then uses that data, and a built in processor to host graphics and information on the display.\\
+\\
+To utilize other displays such as monitors or larger HMI's that accept HDMI, the Altronic Compute Module can take in the ethernet connection from the DE-4000 and allow any HDMI based display to be connected.\\
+\\
+Installation is plug and play, documentation for the ACM-4000 can be found [[https://www.altronic.a2hosted.com/doku.php?id=documents:acm-4000|Here - ACM-4000 Documentation]]
 ===== - CONTROLLER MODULE (691759-1) =====
@@ Line 416: / Line 429: @@
 ==== - TEMPERATURE TRANSDUCER ====
-Temperature transducers, Altronic P/N 691202-300, 691203-300, and
+Temperature transducers, Altronic P/N 691202-300/691203-300,
--450, 691212-450 are packaged in a sealed, stainless steel housing
+-450/691213-450, and 691212-232/691213-232 are packaged in a sealed, stainless steel housing
 with a 5/8"-18 UNF threaded body and a Packard Electric Metri-Pack connector.
 Temperature transducers 691203/202-300 have a temperature measurement
 range of +5 to 300°F. Temperature transducers 691212/213-450 have a temperature range of -40 to +450°F. During configuration, the 691202/203-300
-transducers are selected as Deg1 Type; the 691212/213-450 transducers are
+transducers are selected as Deg1 Type, the 691212/213-450 transducers are
-selected by choosing Deg2 Type. The three wires from the transducers are: +5
+selected by choosing Deg2 Type, and the 691212/213-232 transducers are selected by choosing Deg3 type. The three wires from the transducers are: +5
 volt excitation, temperature output voltage, and minus return. These wires connect directly to the Terminal Module using cable assembly P/N 693008-x.
@@ Line 711: / Line 724: @@
   * **4-20 mA Input - **Switch Position 1 & 3 ON, 2 & 4 OFF\\
   * **Thermocouple Input - **Switch Position 1, 2, 3, 4 OFF\\
-  * **Analog, DEG1 & 2 Input - **Switch Position 4 ON, 1, 2, 3 OFF\\
+  * **Analog, DEG1, 2, & 3 Input - **Switch Position 4 ON, 1, 2, 3 OFF\\
 **See also input sensor wiring diagram figure 11 below.**
@@ Line 917: / Line 930: @@
 ===== - MODBUS ADDRESS LIST =====
-The Default Modbus Output from the DE4000 is listed below.
+The Default Modbus Output from the DE-4000 is listed below.
 -Bit registers are sent under Node address configured in the 'Global' => 'Network' Menu
 {{ :documents:de4000:modsetting.jpg?600 |}}
@@ Line 1355: / Line 1368: @@
 System. Preferred browsers are Google® Chrome and Firefox.
-● Open the web browser and type in the IP address (98.102.65.174). The DE4000 configuration page will be loaded.
+● Open the web browser and type in the IP address (98.102.65.174). The DE-4000 configuration page will be loaded.
 ===== - List of Figures =====